Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing changed? Glance into the tank, and you may see no water inside. Before you worry, rest assured that correcting this issue is usually easy to accomplish. If you can’t figure it out yourself, you can always arrange toilet repair with an experienced plumber. Follow these recommendations to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first action is to ensure that the water is running. If you or someone in your household recently performed a toilet repair, you probably turned off the water first. Did you forget to turn it back on? To see, turn the water shut-off valve on the wall behind the toilet. If the valve was shut, water ought to now start refilling the tank. If this fails to work, test the water at your sink or another plumbing fixture. If nothing spills out from the tap, you could have a larger water supply issue. Contact your water company to get more details. 

Reposition or Replace the Float Mechanism 

Older toilet models use a float ball to measure the water level as it goes up in the tank. When the ball passes a specified height, the float arm it’s connected to stops the water flow. However, insufficient water might enter the tank if the ball is positioned improperly or the arm is damaged. To adjust the float ball, start by removing the toilet tank lid. Bend the float arm up slightly to adjust where it sits in the tank. If this doesn’t fix the problem, you could need to replace the full float mechanism. You should be able to do this yourself by following the directions that come with the replacement parts, or you can work with a plumber for help. Just realize that float balls are old toilet systems. You may appreciate improved dependability and efficiency if you upgrade the existing tank components or replace the toilet entirely. 

Adjust the Fill Valve 

Newer toilets utilize a float cup in place of a float ball, coupled with a fill valve and water level rod. There may be no water in the toilet tank because the valve has slipped out of place or become plugged. Here are a few]] {tips to attempt: 

• Adjust the fill valve: Glance inside the toilet and locate the fill valve on top of a vertical tube device on the left side of the tank. Verify that it’s secure and evenly connected to the tube. Then, change the water level. Current models of toilets have an adjustment knob you can turn manually, while older versions may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and make it possible for the tank refill to check the water level. Modify it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
• Clean the fill valve: Mineral buildup and other gunk could be blocking the valve and preventing your toilet from filling. Turn off the water behind the toilet and remove the fill cap. Then, gradually turn the water back on, cupping your hand over the valve to prevent water from spraying everywhere. After several seconds, turn the water back off. Finally, clean off the fill cap to clear away hard water buildup. If the cap is broken, replace it. 
• Clean the valve tube: The tube below the fill valve might also be blocked. Shut off the water and take off the valve hardware. Then, place a slim bottle brush or wire down the tube. Turn the water back on slightly to flush away the blockage. Replace the valve hardware and flush the toilet to assess your efforts. 

Repair or Replace the Trip Assembly 

If you’ve attempted the steps above without positive results, the final possibility is a broken trip assembly. This element attaches the flush handle to the tank. If it’s broken or positioned improperly, the flush cycle may not complete, leaving the tank bone dry. Remove the toilet tank lid and check the trip assembly attached to the handle. If it’s out of place, reposition it. If the assembly is bent, worn or wrecked, replace it. Whether you complete the job yourself or leave it to a plumber, this simple repair should get your toilet tank filled with water once again. 

Schedule Toilet Repair Today 

You can’t go long without a functional toilet, so reach out to [Company name] to request a toilet repair. We can figure out why your toilet isn’t filling and suggest the right fix. If your plumbing fixture is older and worn out, our team can install a high-efficiency toilet in your bathroom. Be assured that every plumbing repair and replacement we perform is backed by a 100% satisfaction guarantee. To schedule an evaluation from one of our licensed team members, please call your community Service Experts Heating, Air Conditioning & Plumbing office today.